Soil Instruments Smart In-Place Inclinometer (Smart IPI)

Soil Instruments Smart In-Place Inclinometer (Smart IPI) - Image 2

Soil Instruments Smart In-Place Inclinometer (Smart IPI)

The Smart In-Place Inclinometer (Smart IPI) System is used to remotely monitor lateral displacement within a vertical borehole. The Smart IPI System has been designed to supersede traditional IPI systems; with advanced technology and new mechanical design, the Smart IPI is seen as a new product rather than just an improvement to the old. The Smart IPI System comprises in its most basic form a Data Acquisition system, a Sensor Interface Module, one Top Support Assembly, up to 39 Smart IPI Sensors and one Terminating Sensor. The Easy-Connect Coupling and single cable approach lead to a much easier, quicker and more efficient installation as well as an increased number of sensors per borehole.

For more information go to: https://soil.co.uk/products/inclination/

Изпратете запитване

Send an inquiry

PRODUCT FEATURES

Biaxial MEMS Sensors
Single cable system
Sensor strings give a readily automated profile of vertical or horizontal displacements
Factory allocated serial numbers
Onsite allocation of sensor IDs
Mechanical/electrical connection rated IP68 to 2000 kPa
Accurate and precise measurements using MEMS sensors

PRODUCT BENEFITS

Easy to automate using data acquisition system and ‘Argus’ software
Removes the need for manual monitoring
Fast onsite installation with minimal cable management
Plug-and-play into Sensor Interface Module (S.I.M.)
Calibration factor stored in each sensor allow output in engineering units
Up to 40 Smart IPI sensors per borehole
Ability to add to the network as and when required

Модел	Smart In-Place Inclinometer
Диапазон на калибриране	±10°
Резолюция*	0.001% от пълната скала
Точност на сензора	±0.05% от пълната скала
Работна температура	от -10 до +50°C
Повтаряемост	±0.006% от пълната скала
Минимален вътрешен диаметър на корпуса	56mm
Максимален вътрешен диаметър на корпуса	72mm
Размери	192mm x Ø32mm
Входен волтаж	11 - 16 VDC
Текущо потребление за сензор	23mA
Максимален брой сензори за низ	40
Максимално разстояние от логера до сондажа	200m
Защита срещу проникване	IP68 до 200mH2O (2000kPa)
Сглобяване на основа за сензор
Дължина на основата	1m	2m	3m
Материал	Неръждаема стомана
Размери	Ø34mm x 1.040m	Ø34mm x 2.040m	Ø34mm x 3.040m
Тегло	1.43kg	1.88kg	2.31kg
Свързване на сензора
Материал	Неръждаема стомана
Размери	Ø36mm x 310mm
Тегло	0.78kg
Поддържащ монтаж на върха
Дължина на основата	1m	2m	3m
Обща дължина	1.79m	2.79m	3.79m
Тегло	2.9kg	3.3kg	3.7kg
Обхват на настройка	900mm
Материал	Неръждаема стомана
Дейталогер
Тип	Campbell CR800	Campbell CR1000
Възможности за комуникация	Клетъчен GSM/GPRS \| RS485 \| Ethernet \| USB
Възможности за захранване	110 - 240 VAC или 12V батерия със слънчево захранване или обикновена батерия
Работна температура	от -20 до +50°C
IP оценка	IP65
Брой на сондажите	1 - 2	1 - 6

*В зависимост от оборудването

brochure soil instruments smart in-place

manual soil instruments smart in-place

PRODUCT FEATURES

Biaxial MEMS Sensors
Single cable system
Sensor strings give a readily automated profile of vertical or horizontal displacements
Factory allocated serial numbers
Onsite allocation of sensor IDs
Mechanical/electrical connection rated IP68 to 2000 kPa
Accurate and precise measurements using MEMS sensors

PRODUCT BENEFITS

Easy to automate using data acquisition system and ‘Argus’ software
Removes the need for manual monitoring
Fast onsite installation with minimal cable management
Plug-and-play into Sensor Interface Module (S.I.M.)
Calibration factor stored in each sensor allow output in engineering units
Up to 40 Smart IPI sensors per borehole
Ability to add to the network as and when required

Model	Smart In-Place Inclinometer
Calibration range	±10°
Resolution*	0.001% of full scale
Sensor accuracy	±0.05% of full scale
Operating temperature	from -10 to +50°C
Repeatability	±0.006% of full scale
Minimum inside diameter of casing	56mm
Maximum internal casing diameter	72mm
Sizes	192mm x Ø32mm
Input Voltage	11 - 16 VDC
Current consumption for sensor	23mA
Maximum number of string sensors	40
Maximum distance from the logger to the borehole	200m
Intrusion Protection	IP68 up to 200mH2O (2000kPa)
Sensor base assembly
Length of base	1m	2m	3m
Material	Stainless Steel
Sizes	Ø34mm x 1.040m	Ø34mm x 2.040m	Ø34mm x 3.040m
Weight	1.43kg	1.88kg	2.31kg
Sensor Connection
Material	Stainless Steel
Sizes	Ø36mm x 310mm
Weight	0.78kg
Supporting top mount
Length of base	1m	2m	3m
Total length	1.79m	2.79m	3.79m
Weight	2.9kg	3.3kg	3.7kg
Setting range	900mm
Material	Stainless Steel
Datalogger
Type	Campbell CR800	Campbell CR1000
Communication Features	Cellular GSM/GPRS \| RS485 \| Ethernet \| USB
Power Options	110 - 240 VAC or 12V solar battery or regular battery
Operating temperature	from -20 to +50°C
IP rating	IP65
Number of wells	1 - 2	1 - 6